|
|
|
|
|
|
|
|


Register To Receive Our
Monthly Around the House Newsletter Full of home and
money saving tips!
Sign
up today!
|
|
|
HVAC Home
>> HVAC Resource Center
>> Carbon Monoxide
Carbon Monoxide In The Spotlight
Carbon monoxide (CO) poisoning has been one of the more under-publicized
household hazards until two recent events put it in the spotlight. One was the
accidental death in September 1994 of tennis star Vitas Gerulaitas, who
succumbed to CO while sleeping in a rented home. The other was an ordinance that
went into effect October 1, 1994, in Chicago requiring CO detectors in all
residences heated by any fossil fuel burning equipment - in effect, all except
solar or electrically heated homes. The Chicago law was in reaction to a tragedy
that occurred in 1991 when a family of 10 was wiped out by CO poisoning from a
faulty furnace installation.
The Consumer Product Safety Commission says that "at least" 250 people are
killed each year from CO, a very conservative estimate. The American Medical
Association says it's more like 1,500 people a year, with another 10,000 or more
taking ill.
There is a lot of uncertainty because CO is tasteless, colorless and odorless -
undetectable except by sophisticated gear. Also, the main symptoms of CO
poisoning - fatigue, headaches, dizzy spells and nausea - resemble those of the
flu and many other common illnesses. Thus CO poisoning is easily misdiagnosed,
and people can succumb to it with very little physical discomfort, almost like
falling asleep. (Early news reports treated Gerulaitas' death as mysterious and
were filled with speculation about drugs or foul play.)
CO is given off by incomplete combustion of flammable fuels such as natural gas,
oil, wood, coal or kerosene. Common household appliances such as furnaces,
boilers, water heaters and stoves are all potential sources of CO gas. All of
these products are designed with elaborate safeguards and under normal operating
conditions all the CO produced from combustion will be harmlessly vented to the
atmosphere.
Poor venting, due to leaks or blockages in the vent system, is the most common
cause of CO build-up in the home, followed by cracks or corrosion in a furnace's
heat exchanger. Here are some danger signs and steps you can take to minimize
the danger:
Most important, have your furnace or boiler regularly inspected, at least once a
year, by a licensed, competent heating professional. The technician should check
all connections to flue piping and vents for cracks, gaps, rust, corrosion or
debris. Likewise the inspection should cover the combustion chamber and heat
exchanger for cracks, holes, metal fatigue or corrosion, as well as the filters
and filtering system for dirt and blockages. Debris should be cleared off the
burner and safety switches tested.
A yellow , lazy-looking flame in a natural gas furnace indicates inefficient
fuel burning, and consequently higher levels of carbon monoxide. An inefficient
oil furnace will give off an oily odor - but remember, you can't smell CO
itself.
Chimneys and vents ought to be inspected regularly for blockages caused by
debris, animal nests or cave-ins. Also beware of cracks and holes. Inspect
fireplaces for blocked flues, excess soot and debris.
Be sure all vents are properly installed - including those leading from the
clothes dryer, water heater and wood-burning stoves.
Never use an unvented space heater indoors. Never burn charcoal inside and do
not use your gas stove as a heater. When cooking, keep the oven door closed.
Avoid running both a furnace and fireplace simultaneously for long periods of
time. This can create serious backdrafting that prevents CO gas from exiting the
home. Never install a boiler, furnace or water heater in an airtight enclosure.
Look for the following signs that may indicate CO problems - streaks of soot
around the service door of a gas appliance; rust spots on flue pipe, boilers,
furnaces or water heaters; excessive moisture on basement windows, which may
indicate poor ventilation; generally stale air throughout the house, another
sign of poor ventilation.
DO INSTALL AN UL-APPROVED CO DETECTOR
The UL standard requires home CO detectors to sound a warning before CO levels
reach over 100 parts per million (ppm) over 90 minutes, 200 ppm over 35 minutes
or 400 ppm over 15 minutes. These warning should allow the average person to
safely evacuate the premises. (CO levels over 200 ppm lasting for 90 minutes can
cause headaches in healthy adults. At 300 ppm the healthy adult may experience
drowsiness, at 400 ppm might collapse and 500 ppm exposure could result in brain
damage or death.)
Approved CO detectors are readily available at home improvement centers or from
your service company. They are similar to smoke detectors in both appearance and
installation. The best place to install a CO detector is near bedrooms. Don't
install one in the boiler or furnace room the garage or the kitchen, where it
may go off in reaction to temporary elevated levels of CO.
What do you do if the alarm sounds? Vacate the house quickly, opening doors and
windows as you leave in order to provide ventilation. Then contact a local
emergency service crew - usually the police or fire department - for advice.
Depending on your community, they may have a CO measuring device on hand to take
a reading inside your home in order to determine if it is safe to move back in.
Keep in mind that the act of ventilating your home may make it safe for
immediate occupancy but won't fix whatever generated excess CO in the first
place. As soon as possible you need a professional inspection of all possible CO
sources. This should be someone equipped with CO measuring gear able to detect
concentrations as small as 5-10 parts per million. The measurement test should
be conducted over at least a 24-hour period.
It is possible for a CO alarm to be triggered by a single unusual incident that
presents no lasting threat. However, if one ever goes off in your home, you
won't rest easily until you take all the precautions possible to safeguard
yourself and loved ones.
If you are looking for a Cleveland area air conditioning contractor, please call us today at (216) 214-0945 or complete our service request form.
|
|
|
| |
|
|
|
| Service Areas |
HVAC Articles |
Free Newsletter |
Request Service|
Home Page
|
|
Design Air Heating & Cooling •
15874 Agnes Blvd
Brook Park, OH 44142
PHONE: (216) 214-0945 • FAX: (216) 267-6818
State Of Ohio License #27914
Cleveland Energy Audits
Preferred Local Vendors
©2007
Design Air Heating & Cooling. All Rights Reserved.
No part of this site may be
reproduced in any form without
the copyright holder's written
permission.
HVAC Contractors |
|
Areas We Provide HVAC Service In, Ohio
Brook Park, OH, Middleburg Hts., OH, Strongsville, OH, Berea, OH, Cleveland, OH, Avon, OH, Avon Lake, OH, Bay Village, OH, Westlake, OH, North Olmsted, OH, North Royalton, OH, Parma, OH, Brooklyn, OH, Brecksville, OH, Broadview Hts., OH, Fairview Park, OH, Independence, OH, Lakewood, OH, Olmsted Falls, OH, Rocky River, OH, Seven Hills, OH |
|
|
|
|